V1.06 (For Magic-S Rev 1.1)
1.Supports Xbox Elite Wireless Controller Series 2
Xbox Elite Wireless Controller Series 2 Start Up
① Turn on your PS4, PS3, NEOGEO mini, or PS Classic system, and connect the system to your TV.
② Connect the Magic S in o any spare USB port on your system.
③ To switch the modes, press and hold the button on the side of the adapter for 3-5 seconds. The LED indicator blinks slowly.
④ Turn on your Xbox Elite 2 controller
⑤ To sync your Xbox Elite 2 controller and the adapter, press the Button on the side of the adapter, and then press the SYNC button on your controller. The LED indicator blinks quickly.
⑥ The adapter and your controller has been connected if the LED indicator lights up. And your controller is now ready to use.
Special Remarks:
- It may take a longer time to connect your Xbox Elite 2 and Magic-S adapter. And the connection may be disconnected shortly (The lights on the controller and the adapter flash) and then connect again during the Bluetooth pairing process. Please wait patiently until the LED indicators on the controller and the adapter stop flashing.
- If you want to disconnect the controller and the adapter, please press and hold the HOME button on your controller to shut off the power.
- If the Bluetooth connection failed, you can repeat the above steps to try again. Please make sure you pull out the adapter and plug it to the system again, and restart your controller before a new connection.
2.Adjust the Dead Zone
① Press and hold the two buttons START and D-Pad Left (For the left stick) or D-Pad Right (For the right stick). The LED indicator on the adapter flash.
② To increase or decrease the dead zone, press the D-Pad “Up” or “Down”.
③ As soon as you get the right dead zone value, you may release the button “START” to quit the Dead Zone Adjusting.
④ There are 7 levels of the Dead Zone Value.
Dead Zone Level 1: 0%
Dead Zone Level 2: 2.5%
Dead Zone Level 3: 5%
Dead Zone Level 4: 7.5%
Dead Zone Level 5: 10%
Dead Zone Level 6: 12.5%
Dead Zone Level 7: 15%
The default one is the Level 3.
You can know the Dead Zone Level by the times of the LED indicator flashing on the adapter during the adjusting process. For example, the LED indicator flashes 3 times then stop flashing when the Dead Zone Level is Level 3.
3.Compatible with ASTRO Gaming C40 TR Controller PlayStation 4 and PlayStation 4 SCUF Vantage 2 controller by a USB cable (Wired connection).
4.Add the analog input to the Joy-Cons.
5.Supports SEGA MEGA DRIVE and SEGA Genesis Mini entertainment system. The LED indicator is White.
6.Supports the USB Control Pads of SEGA MEGA DRIVE and SEGA Genesis Mini
Quick Start
Download the software from https://www.mayflash.com/Support and install it on your Windows system.
Double click on the updater and leave the updater window open on your screen.
Press and hold the button on the side of the adapter, and connect the USB from your adapter in o any spare port on your PC.
As soon as the driver window indicates under “Device” that the adapter has been recognized, you may release the button.
select “update”.
Do not disconnect the device until you are informed that the updated was completed successfully.
Switch Pro mode (the LED indicator is purple)
To make sure the system can identify the adapter easily, please turn on the “Pro Controller Wired Communication” of the Nintendo Switch system.
once you switch the adapter to the Switch Pro mode (the LED indicator is purple) .
Tips: System Settings - Controllers and Sensors - Pro Controller Wired Communication – ON.
More Instructions
Download the firmware from https://www.mayflash.com/Support and install it on your Windows system.
Press and hold the button on the side of the adapter, and connect the USB from your adapter in o any spare port on your PC, and wait for 3-5 seconds. After completing the above steps, the program automatically identifies the adapter (LED indicator turns off).
Click "update" and wait for a few seconds. The update is completed when the progress bar reaches 100%.
Note: Do not disconnect the device until you are informed that the updated was completed successfully
Press "OK" to complete the update.